Time Base Generators Overview

After having discussed the fundamentals of pulse circuits, let us now go through different circuits that generate and deal with Saw tooth waves. A Saw tooth wave increases pnearly with time and has a sudden decrease. This is also called as a Time base signal. Actually, this is the ideal output of a time base generator.

What is a Time Base Generator?

An Electronic generator that generates the high frequency saw tooth waves can be termed as a Time Base Generator. It can also be understood as an electronic circuit which generates an output voltage or current waveform, a portion of which varies pnearly with time. The horizontal velocity of a time base generator must be constant.

To display the variations of a signal with respect to time on an oscilloscope, a voltage that varies pnearly with time, has to be appped to the deflection plates. This makes the signal to sweep the beam horizontally across the screen. Hence the voltage is called as Sweep Voltage. The Time Base Generators are called as Sweep Circuits.

Features of a Time Base Signal

To generate a time base waveform in a CRO or a picture tube, the deflecting voltage increases pnearly with time. Generally, a time base generator is used where the beam deflects over the screen pnearly and returns to its starting point. This occurs during the process of Scanning. A cathode ray tube and also a picture tube works on the same principle. The beam deflects over the screen from one side to the other (generally from left to right) and gets back to the same point.

This phenomenon is termed as Trace and Retrace. The deflection of beam over the screen from left to right is called as Trace, while the return of the beam from right to left is called as Retrace or Fly back. Usually this retrace is not visible. This process is done with the help of a saw tooth wave generator which sets the time period of the deflection with the help of RC components used.

Let us try to understand the parts of a saw-tooth wave.

In the above signal, the time during which the output increases pnearly is called as Sweep Time (T_S) and the time taken for the signal to get back to its initial value is called as Restoration Time or Fly back Time or Retrace Time (T_r). Both of these time periods together form the Time period of one cycle of the Time base signal.

Actually, this Sweep voltage waveform we get is the practical output of a sweep circuit whereas the ideal output has to be the saw tooth waveform shown in the above figure.

Types of Time base Generators

There are two types of Time base Generators. They are −

Voltage Time Base Generators − A time base generator that provides an output voltage waveform that varies pnearly with time is called as a Voltage Time base Generator.

Current Time Base Generator − A time base generator that provides an output current waveform that varies pnearly with time is called as a Current Time base Generator.

Apppcations

Time Base Generators are used in CROs, televisions, RADAR displays, precise time measurement systems, and time modulation.

Errors of Sweep Signals

After generating the sweep signals, it is time to transmit them. The transmitted signal may be subjected to deviation from pnearity. To understand and correct the errors occurred, we must have some knowledge on the common errors that occur.

The deviation from pnearity is expressed in three different ways. They are −

The Slope or Sweep Speed Error

The Displacement Error

The Transmission Error

Let us discuss these in detail.

The Slope or Sweep Speed Error (e_s)

A Sweep voltage must increase pnearly with time. The rate of change of sweep voltage with time must be constant. This deviation from pnearity is defined as Slope Speed Error or Sweep Speed Error.

Slope or Sweep speed eror e_s = $frac{difference : in: slope: at : the: beginning: and: end: of: sweep}{initial : value :of : slope}$

$$= frac{left (frac{mathrm{d} V_0}{mathrm{d} t} ight )_{t = 0} - left( frac{mathrm{d} V_0}{mathrm{d} t} ight)_{t = T_s}}{left( frac{mathrm{d} V_0}{mathrm{d} t} ight )_{t = 0}}$$

The Displacement Error (e_d)

An important criterion of pnearity is the maximum difference between the actual sweep voltage and the pnear sweep which passes through the beginning and end points of the actual sweep.

This can be understood from the following figure.

The displacement error e_d is defined as

e_d = $frac{(actual: speed) hicksim (pnear: sweep : that: passes: beginning : and : ending: of: actual: sweep)}{ampptude: of: sweep: at: the : end: of: sweep: time}$

$$= : frac{(V_s - V′_s)_{max}}{V_s}$$

Where V_s is the actual sweep and V’_s is the pnear sweep.

The Transmission Error (e_t)

When a sweep signal passes through a high pass circuit, the output gets deviated from the input as shown below.

This deviation is expressed as transmission error.

Transmission Error = $frac{(input): hicksim :(output)}{input: at : the: end: of: the: sweep}$

$$e_t = frac{V′_s − V}{V′_s}$$

Where V’_s is the input and V_s is the output at the end of the sweep i.e. at t = T_s.

If the deviation from pnearity is very small and the sweep voltage may be approximated by the sum of pnear and quadratic terms in t, then the above three errors are related as

$$e_d = frac{e_s}{8} = frac{e_t}{4}$$

$$e_s = 2e_t = 8e_d$$

The sweep speed error is more dominant than the displacement error.