- Indirect Type ADC
- Direct Type ADCs
- DAC Example Problem
- Digital to Analog Converters
- Data Converters
- Voltage Regulators
- Phase Locked Loop Ic
- 555 Timer
- Waveform Generators
- Sinusoidal Oscillators
- Active Filters
- Clampers
- Clippers
- Rectifiers
- Log & Anti-Log Amplifiers
- Comparators
- Converters Of Electrical Quantities
- Differentiator & Integrator
- Arithmetic Circuits
- Op-Amp applications
- Basics Operational Amplifier
- Basics of Integrated Circuits Applications
- Home
Useful Resources
Selected Reading
- Who is Who
- Computer Glossary
- HR Interview Questions
- Effective Resume Writing
- Questions and Answers
- UPSC IAS Exams Notes
Clampers
In the previous chapter, we discussed about cpppers. Now, let us discuss about other type of wave shaping circuits, namely clampers.
Op-amp based Clampers
A clamper is an electronic circuit that produces an output, which is similar to the input but with a shift in the DC level. In other words, the output of a clamper is an exact reppca of the input. Hence, the peak to peak ampptude of the output of a clamper will be always equal to that of the input.
Clampers are used to introduce or restore the DC level of input signal at the output. There are two types of op-amp based clampers based on the DC shift of the input.
Positive Clamper
Negative Clamper
This section discusses about these two types of clampers in detail.
Positive Clamper
A positive clamper is a clamper circuit that produces an output in such a way that the input signal gets shifted vertically by a positive DC value.
The circuit diagram of a positive clamper is shown in the following figure −
![Positive Cppper Circuit](/pnear_integrated_circuits_apppcations/images/positive_clamper.jpg)
In the above circuit, a sinusoidal voltage signal, $V_{i}$ is appped to the inverting terminal of op-amp through a network that consists of a capacitor $C_{1}$ and a resistor $R_{1}$. That means, AC voltage signal is appped to the inverting terminal of the op-amp.
The DC reference voltage $V_{ref}$ is appped to the non-inverting terminal of the op-amp. The value of reference voltage $V_{ref}$ can be chosen by varying the resistor $R_{2}$. In this case, we will get a reference voltage $V_{ref}$ of a positive value.
The above circuit produces an output, which is the combination (resultant sum) of the sinusoidal voltage signal $V_{i}$ and the reference voltage $V_{ref}$. That means, the clamper circuit produces an output in such a way that the sinusoidal voltage signal $V_{i}$ gets shifted vertically upwards by the value of reference voltage $V_{ref}$.
The input wave form and the corresponding output wave form of positive clamper are shown in above figure −
![Positive Cppper Circuit](/pnear_integrated_circuits_apppcations/images/positive_clamper_eg.jpg)
From the figure above, you can observe that the positive clamper shifts the appped input waveform vertically upward at the output. The amount of shift will depend on the value of the DC reference voltage.
Negative Clamper
A negative clamper is a clamper circuit that produces an output in such a way that the input signal gets shifted vertically by a negative DC value.
The circuit diagram of negative clamper is shown in the following figure −
![Positive Cppper Circuit](/pnear_integrated_circuits_apppcations/images/negative_clamper.jpg)
In the above circuit, a sinusoidal voltage signal $V_{i}$ is appped to the inverting terminal of the op-amp through a network that consists of a capacitor C1 and resistor $R_{1}$. That means, AC voltage signal is appped to the inverting terminal of the op-amp.
The DC reference voltage $V_{ref}$ is appped to the non-inverting terminal of the op-amp.The value of reference voltage $V_{ref}$ can be chosen by varying the resistor $R_{2}$. In this case,we will get reference voltage $V_{ref}$ of a negative value.
The above circuit produces an output, which is the combination (resultant sum) of sinusoidal voltage signal $V_{i}$ and reference voltage $V_{ref}$. That means, the clamper circuit produces an output in such a way that the sinusoidal voltage signal $V_{i}$ gets shifted vertically downwards by the value of reference voltage $V_{ref}$.
The input wave form and the corresponding output wave form of a negative clamper are shown in the following figure −
![Negative Clampler Eg](/pnear_integrated_circuits_apppcations/images/negative_clamper_eg.jpg)
We can observe from the output that the negative clamper shifts the appped input waveform vertically downward at the output. The amount of shifting will depend on the value of DC reference voltage.
Advertisements