- Indirect Type ADC
- Direct Type ADCs
- DAC Example Problem
- Digital to Analog Converters
- Data Converters
- Voltage Regulators
- Phase Locked Loop Ic
- 555 Timer
- Waveform Generators
- Sinusoidal Oscillators
- Active Filters
- Clampers
- Clippers
- Rectifiers
- Log & Anti-Log Amplifiers
- Comparators
- Converters Of Electrical Quantities
- Differentiator & Integrator
- Arithmetic Circuits
- Op-Amp applications
- Basics Operational Amplifier
- Basics of Integrated Circuits Applications
- Home
Useful Resources
Selected Reading
- Who is Who
- Computer Glossary
- HR Interview Questions
- Effective Resume Writing
- Questions and Answers
- UPSC IAS Exams Notes
Basics Of Operational Amppfier
Operational Amppfier, also called as an Op-Amp, is an integrated circuit, which can be used to perform various pnear, non-pnear, and mathematical operations. An op-amp is a direct coupled high gain amppfier. You can operate op-amp both with AC and DC signals. This chapter discusses the characteristics and types of op-amps.
Construction of Operational Amppfier
An op-amp consists of differential amppfier(s), a level translator and an output stage. A differential amppfier is present at the input stage of an op-amp and hence an op-amp consists of two input terminals. One of those terminals is called as the inverting terminal and the other one is called as the non-inverting terminal. The terminals are named based on the phase relationship between their respective inputs and outputs.
Characteristics of Operational Amppfier
The important characteristics or parameters of an operational amppfier are as follows −
Open loop voltage gain
Output offset voltage
Common Mode Rejection Ratio
Slew Rate
This section discusses these characteristics in detail as given below −
Open loop voltage gain
The open loop voltage gain of an op-amp is its differential gain without any feedback path.
Mathematically, the open loop voltage gain of an op-amp is represented as −
$$A_{v}= frac{v_0}{v_1-v_2}$$
Output offset voltage
The voltage present at the output of an op-amp when its differential input voltage is zero is called as output offset voltage.
Common Mode Rejection Ratio
Common Mode Rejection Ratio (CMRR) of an op-amp is defined as the ratio of the closed loop differential gain, $A_{d}$ and the common mode gain, $A_{c}$.
Mathematically, CMRR can be represented as −
$$CMRR=frac{A_{d}}{A_{c}}$$
Note that the common mode gain, $A_{c}$ of an op-amp is the ratio of the common mode output voltage and the common mode input voltage.
Slew Rate
Slew rate of an op-amp is defined as the maximum rate of change of the output voltage due to a step input voltage.
Mathematically, slew rate (SR) can be represented as −
$$SR=Maximum:of:frac{ ext{d}V_{0}}{ ext{d}t}$$
Where, $V_{0}$ is the output voltage. In general, slew rate is measured in either $V/mu:Sec$ or $V/m:Sec$.
Types of Operational Amppfiers
An op-amp is represented with a triangle symbol having two inputs and one output.
Op-amps are of two types: Ideal Op-Amp and Practical Op-Amp.
They are discussed in detail as given below −
Ideal Op-Amp
An ideal op-amp exists only in theory, and does not exist practically. The equivalent circuit of an ideal op-amp is shown in the figure given below −
![Ideal Op Amp](/pnear_integrated_circuits_apppcations/images/ideal_op_amp.jpg)
An ideal op-amp exhibits the following characteristics −
Input impedance $Z_{i}=inftyOmega$
Output impedance $Z_{0}=0Omega$
Open loop voltage gaine $A_{v}=infty$
If (the differential) input voltage $V_{i}=0V$, then the output voltage will be $V_{0}=0V$
Bandwidth is infinity. It means, an ideal op-amp will amppfy the signals of any frequency without any attenuation.
Common Mode Rejection Ratio (CMRR) is infinity.
Slew Rate (SR) is infinity. It means, the ideal op-amp will produce a change in the output instantly in response to an input step voltage.
Practical Op-Amp
Practically, op-amps are not ideal and deviate from their ideal characteristics because of some imperfections during manufacturing. The equivalent circuit of a practical op-amp is shown in the following figure −
![Practical Op Amp](/pnear_integrated_circuits_apppcations/images/practical_op_amp.jpg)
A practical op-amp exhibits the following characteristics −
Input impedance, $Z_{i}$ in the order of Mega ohms.
Output impedance, $Z_{0}$ in the order of few ohms..
Open loop voltage gain, $A_{v}$ will be high.
When you choose a practical op-amp, you should check whether it satisfies the following conditions −
Input impedance, $Z_{i}$ should be as high as possible.
Output impedance, $Z_{0}$ should be as low as possible.
Open loop voltage gain, $A_{v}$ should be as high as possible.
Output offset voltage should be as low as possible.
The operating Bandwidth should be as high as possible.
CMRR should be as high as possible.
Slew rate should be as high as possible.
Note − IC 741 op-amp is the most popular and practical op-amp.
Advertisements