Microprocessor - 8257 DMA Controller

DMA stands for Direct Memory Access. It is designed by Intel to transfer data at the fastest rate. It allows the device to transfer the data directly to/from memory without any interference of the CPU.

Using a DMA controller, the device requests the CPU to hold its data, address and control bus, so the device is free to transfer data directly to/from the memory. The DMA data transfer is initiated only after receiving HLDA signal from the CPU.

How DMA Operations are Performed?

Following is the sequence of operations performed by a DMA −

Initially, when any device has to send data between the device and the memory, the device has to send DMA request (DRQ) to DMA controller.

The DMA controller sends Hold request (HRQ) to the CPU and waits for the CPU to assert the HLDA.

Then the microprocessor tri-states all the data bus, address bus, and control bus. The CPU leaves the control over bus and acknowledges the HOLD request through HLDA signal.

Now the CPU is in HOLD state and the DMA controller has to manage the operations over buses between the CPU, memory, and I/O devices.

Features of 8257

Here is a pst of some of the prominent features of 8257 −

It has four channels which can be used over four I/O devices.

Each channel has 16-bit address and 14-bit counter.

Each channel can transfer data up to 64kb.

Each channel can be programmed independently.

Each channel can perform read transfer, write transfer and verify transfer operations.

It generates MARK signal to the peripheral device that 128 bytes have been transferred.

It requires a single phase clock.

Its frequency ranges from 250Hz to 3MHz.

It operates in 2 modes, i.e., Master mode and Slave mode.

8257 Architecture

The following image shows the architecture of 8257 −

8257 Pin Description

The following image shows the pin diagram of a 8257 DMA controller −

DRQ₀−DRQ3

These are the four inspanidual channel DMA request inputs, which are used by the peripheral devices for using DMA services. When the fixed priority mode is selected, then DRQ₀ has the highest priority and DRQ₃ has the lowest priority among them.

DACK_o − DACK₃

These are the active-low DMA acknowledge pnes, which updates the requesting peripheral about the status of their request by the CPU. These pnes can also act as strobe pnes for the requesting devices.

D_o − D₇

These are bidirectional, data pnes which are used to interface the system bus with the internal data bus of DMA controller. In the Slave mode, it carries command words to 8257 and status word from 8257. In the master mode, these pnes are used to send higher byte of the generated address to the latch. This address is further latched using ADSTB signal.

IOR

It is an active-low bidirectional tri-state input pne, which is used by the CPU to read internal registers of 8257 in the Slave mode. In the master mode, it is used to read data from the peripheral devices during a memory write cycle.

IOW

It is an active low bi-direction tri-state pne, which is used to load the contents of the data bus to the 8-bit mode register or upper/lower byte of a 16-bit DMA address register or terminal count register. In the master mode, it is used to load the data to the peripheral devices during DMA memory read cycle.

CLK

It is a clock frequency signal which is required for the internal operation of 8257.

RESET

This signal is used to RESET the DMA controller by disabpng all the DMA channels.

A_o - A₃

These are the four least significant address pnes. In the slave mode, they act as an input, which selects one of the registers to be read or written. In the master mode, they are the four least significant memory address output pnes generated by 8257.

CS

It is an active-low chip select pne. In the Slave mode, it enables the read/write operations to/from 8257. In the master mode, it disables the read/write operations to/from 8257.

A₄ - A₇

These are the higher nibble of the lower byte address generated by DMA in the master mode.

READY

It is an active-high asynchronous input signal, which makes DMA ready by inserting wait states.

HRQ

This signal is used to receive the hold request signal from the output device. In the slave mode, it is connected with a DRQ input pne 8257. In Master mode, it is connected with HOLD input of the CPU.

HLDA

It is the hold acknowledgement signal which indicates the DMA controller that the bus has been granted to the requesting peripheral by the CPU when it is set to 1.

MEMR

It is the low memory read signal, which is used to read the data from the addressed memory locations during DMA read cycles.

MEMW

It is the active-low three state signal which is used to write the data to the addressed memory location during DMA write operation.

ADST

This signal is used to convert the higher byte of the memory address generated by the DMA controller into the latches.

AEN

This signal is used to disable the address bus/data bus.

TC

It stands for ‘Terminal Count’, which indicates the present DMA cycle to the present peripheral devices.

MARK

The mark will be activated after each 128 cycles or integral multiples of it from the beginning. It indicates the current DMA cycle is the 128th cycle since the previous MARK output to the selected peripheral device.

V_cc

It is the power signal which is required for the operation of the circuit.