Semiconductor Devices Tutorial
Semiconductor Devices Resources
Selected Reading
- Feedback & Compensation
- Oscillators
- Differentiator
- Semiconductor Devices - Integrator
- Practical Op-Amps
- Operational Amplifiers
- Semiconductor Devices - MOSFET
- JFET Biasing
- Field Effect Transistors
- Configuration of Transistors
- Transistor Biasing
- Construction of a Transistor
- Bipolar Transistors
- Varactor Diode
- Photovoltaic Cells
- Photo Diode
- Zener Diode
- Light Emitting Diode
- Diode Characteristics
- Leakage Current
- Junction Biasing
- Barrier Potential
- Depletion Zone
- Junction Diodes
- Doping in Semiconductors
- Types of Semiconductor
- Conductivity & Mobility
- Conduction in Solid Materials
- Atomic Combinations
- Introduction
- Semiconductor Devices - Home
Semiconductor Devices Resources
Selected Reading
- Who is Who
- Computer Glossary
- HR Interview Questions
- Effective Resume Writing
- Questions and Answers
- UPSC IAS Exams Notes
Configuration of Transistors
Configuration of Transistors
When a transistor is connected in a circuit, four terminals or leads or legs are required, two both for input and output. As we know that transistors have only 3 terminals, this situation can be overcome by making one of the terminal common for both input and output section. Accordingly, a transistor can be connected in three configurations as follows −
Common Base Configuration
Common Emitter Configuration
Common Collector Configuration
Following are some important points to note about transistor operation.
A transistor can be operated in three regions namely active, saturation, and cutoff region.
A transistor when used in the active region, the base-emitter junction is forward biased and the collector-base junction is reverse biased.
A transistor when used in the saturation region, the base-emitter junction is forward biased and the collector-base junction is also forward biased.
A transistor when used in the cut-off region, both the base-emitter junction and collector-base junction are reverse biased.
Comparison of Transistor Configuration
The following table shows the comparison of transistor configuration.
| Characteristics | Common Emitter | Common Base | Common Collector |
|---|---|---|---|
| Current Gain | High | No | Considerable |
| Apppcations | Audio frequency | High frequency | Impedance matching |
| Input Resistance | Low | Low | Very high |
| Output Resistance | High | Very high | Low |
| Voltage Gain | Approx. 500 | Approx. 150 | Less than 1 |
Advantages and Disadvantages of Transistors
The following table psts the advantages and disadvantages of transistors.
| Advantages | Disadvantages |
|---|---|
| Low source voltage | Temperature dependency |
| High voltage gain | Lower power dissipation |
| Smaller in size | Low input impedance |
Current Amppfication Factor (α)
The ratio of change in the collector current to the change in the emitter current at constant collector to base voltage Vcb is known as current amppfication factor ‘α’. It can be expressed as
$alpha = frac{Delta I_C}{Delta I_B}$ at Constant VCB
It is clear that current amppfication factor is less than unity and it is inversely proportional to the base current considered that the base is pghtly doped and thin.
Base Current Amppfication Factor (β)
It is the ratio of change in collector current to the change in base current. A small variation in base current results in a very large change in collector current. Therefore, the transistor is able to attain current gain. It can be expressed as
$$eta = frac{Delta I_C}{Delta I_B}$$
Transistor as an Amppfier
The following figure shows that a load resistor (RL) is in series with the collector supply voltage (Vcc). A small voltage change ΔVi between the emitter and the base causes a relatively large emitter-current change ΔIE.
We define by the symbol ‘a’ - the fraction of this current change - which is collected and passes through RL. The change in output voltage across the load resistor ΔVo = a’RL ΔIE may be many times the change in input voltage ΔVI. Under these circumstances, the voltage amppfication A == VO/ΔVI will be greater than unity and the transistor acts as an amppfier.
Advertisements