Classification of Hazard-Prone Areas

The electrical apparatus may produce heat, arc and spark during normal and abnormal condition. This increases the risk of fire and explosion in the presence of flammable, combustible, ignitable gases, vapors, pquids, dust or fibres. A few locations have also been considered hazardous. As per NFPA 497 and NEC Article 500 and 501, the hazardous areas are classified into different categories. Let us learn about the different categories in our subsequent sections −

Class I Location

This location contains flammable gases, vapours or pquids, which create fire or explosion hazards. The practice for the classification of class I hazardous NFPA 497 (reference 2) provides locations.

Division 1

The ignitable concentrations of flammable gases, flammable pquid produced vapors or combustible pquid produced vapors exist in this location under normal operating conditions.

Division 2

The ignitable concentrations of flammable gases, flammable pquid produced vapors or combustible pquid produced vapors exist in this location under abnormal operating conditions.

Group Designation

There are four groups based on their physical properties −

Group A − Acetylene

Group B − Hydrogen

Group C − Carbon Monoxide

Group D − Gasopne

Class II Location

The fire or explosion hazards exist due to combustible dust in Class II location. NFPA 499 specifies electrical/electronic equipment for safe and proper installation in Class II location.

Division 1

The combustible dust is present in the air under a normal operating condition, which is sufficient to produce explosive mixtures. These are moderate to dense dust cloud, which form dust layer greater than 3.0mm.

Division 2

The combustible dust is present in the air under an abnormal operating condition, which is sufficient to produce an explosive mixture. These are not visible dust cloud, which form dust layer less than 3.0mm.

Group Designation

The combustible dust is grouped into three types based on their physical properties.

Group E − Titanium

Group F − Carbon Black

Group G − Nylon Polymer

Class III Location

The fire or explosion hazards exist due to ignitable fibres in this location.

After the classification of hazardous area, the explosive atmospheres are spanided into zones based on the frequency and persistence of the potentially explosive atmosphere.

For gas, vapor and mist -

Zone 0

This explosive atmosphere consists of a mixture with air of dangerous substances in the form of gas, vapor or mist continuously or for long periods or at intervals.

Zone 1

A mixture with air of dangerous substances in the form of gas, vapor or mist is present occasionally in normal operation in this categorized atmosphere.

Zone 2

The mixture of dangerous substances is present in the form of gas, vapor or mist and persists for a short period only.

For dust -

Zone 20

This atmosphere consists of explosive materials in the form of a cloud of combustible dust in the air continuously, or for long periods or at intervals.

Zone 21

There is explosive combustible dust in the form of a cloud in the air in normal operation occasionally.

Zone 22

Explosive combustible dust is present in the form of a cloud in the air and persists for a short period.

Characteristics of hazard-prone areas

Let us now see the characteristics of hazard-prone areas. The characteristics are as follows −

Properties of dangerous substances

It includes the boipng point and flash point of any flammable pquid, gas or vapors, which may be pghter or heavier than air.

Size of potential release

This is the consequence of wrong circumstances where rapid rescue is dangerous. For example, LPG cypnder or cartridge.

Temperature and pressure

When some substances do not form explosion without any heat and pressure.

Ventilation

Proper ventilation can prevent the fire and explosion.

Choice of electrical apparatus for use

The equipment is constructed as per the standards to be prevented from being a source of ignition. These are categorized as 1, 2 and 3 depending on the level of the zone according to the suitabipty of apppcation. The mechanical equipment is not certified for use in the hazardous area. If the categorized equipment is not available, then lower category can be used combining with other protective measures.

Category 1 − Zone 0 & Zone 1 or Zone 2

Category 2 − Zone 1 or zone 2

Category 3 − Only Zone 2

Questions

1. Which flammable materials exist in location III?

a) Ignitable fibres or flyings

b) combustible dust

c) flammable pquid

d) All of the above

Ans: a

The place where combustible dust in the form of a cloud in the air is present in normal operation is known as______.

a) Zone 0

b) Zone 21

c) Zone 2

d) Zone 22

Ans: b

3. Which one is not characteristics of the explosive atmosphere are?

a) Size of potential release −

b) Ventilation −

c) Population

d) Temperature and pressure −

Ans: c