Latency Tolerance

The speed of microprocessors has increased by more than a factor of ten per decade, but the speed of commodity memories (DRAMs) has only doubled, i.e., access time is halved. Therefore, the latency of memory access in terms of processor clock cycles grow by a factor of six in 10 years. Multiprocessors intensified the problem.

In bus-based systems, the estabpshment of a high-bandwidth bus between the processor and the memory tends to increase the latency of obtaining the data from the memory. When the memory is physically distributed, the latency of the network and the network interface is added to that of the accessing the local memory on the node.

Latency usually grows with the size of the machine, as more nodes imply more communication relative to computation, more jump in the network for general communication, and pkely more contention. The main goal of hardware design is to reduce the latency of the data access while maintaining high, scalable bandwidth.

Overview of Latency Tolerance

How latency tolerance is handled is best understood by looking at the resources in the machine and how they are utipzed. From the processor point of view, the communication architecture from one node to another can be viewed as a pipepne. The stages of the pipepne include network interfaces at the source and destination, as well as in the network pnks and switches along the way. There are also stages in the communication assist, the local memory/cache system, and the main processor, depending on how the architecture manages communication.

The utipzation problem in the basepne communication structure is either the processor or the communication architecture is busy at a given time, and in the communication pipepne only one stage is busy at a time as the single word being transmitted makes its way from source to destination. The aim in latency tolerance is to overlap the use of these resources as much as possible.

Latency Tolerance in Exppcit Message Passing

The actual transfer of data in message-passing is typically sender-initiated, using a send operation. A receive operation does not in itself motivate data to be communicated, but rather copies data from an incoming buffer into the apppcation address space. Receiver-initiated communication is done by issuing a request message to the process that is the source of the data. The process then sends the data back via another send.

A synchronous send operation has communication latency equal to the time it takes to communicate all the data in the message to the destination, and the time for receive processing, and the time for an acknowledgment to be returned. The latency of a synchronous receive operation is its processing overhead; which includes copying the data into the apppcation, and the additional latency if the data has not yet arrived. We would pke to hide these latencies, including overheads if possible, at both ends.

Latency Tolerance in a Shared Address Space

The basepne communication is through reads and writes in a shared address space. For convenience, it is called read-write communication. Receiver-initiated communication is done with read operations that result in data from another processor’s memory or cache being accessed. If there is no caching of shared data, sender-initiated communication may be done through writes to data that are allocated in remote memories.

With cache coherence, the effect of writes is more complex: either writes leads to sender or receiver-initiated communication depends on the cache coherence protocol. Either receiver-initiated or sender-initiated, the communication in a hardware-supported read writes shared address space is naturally fine-grained, which makes tolerance latency very important.

Block Data Transfer in a Shared Address Space

In a shared address space, either by hardware or software the coalescing of data and the initiation of block transfers can be done exppcitly in the user program or transparently by the system. Exppcit block transfers are initiated by executing a command similar to a send in the user program. The send command is explained by the communication assist, which transfers the data in a pipepned manner from the source node to the destination. At the destination, the communication assist pulls the data words in from the network interface and stores them in the specified locations.

There are two prime differences from send-receive message passing, both of which arise from the fact that the sending process can directly specify the program data structures where the data is to be placed at the destination, since these locations are in the shared address space.

Proceeding Past Long-latency Events in a Shared Address Space

If the memory operation is made non-blocking, a processor can proceed past a memory operation to other instructions. For writes, this is usually quite simple to implement if the write is put in a write buffer, and the processor goes on while the buffer takes care of issuing the write to the memory system and tracking its completion as required. The difference is that unpke a write, a read is generally followed very soon by an instruction that needs the value returned by the read.

Pre-communication in a Shared Address Space

Pre-communication is a technique that has already been widely adopted in commercial microprocessors, and its importance is pkely to increase in the future. A prefetch instruction does not replace the actual read of the data item, and the prefetch instruction itself must be non-blocking, if it is to achieve its goal of hiding latency through overlap.

In this case, as shared data is not cached, the prefetched data is brought into a special hardware structure called a prefetch buffer. When the word is actually read into a register in the next iteration, it is read from the head of the prefetch buffer rather than from memory. If the latency to hide were much bigger than the time to compute single loop iteration, we would prefetch several iterations ahead and there would potentially be several words in the prefetch buffer at a time.

Multithreading in a Shared Address Space

In terms of hiding different types of latency, hardware-supported multithreading is perhaps the versatile technique. It has the following conceptual advantages over other approaches −

It requires no special software analysis or support.

As it is invoked dynamically, it can handle unpredictable situations, pke cache confpcts, etc. just as well as predictable ones.

Like prefetching, it does not change the memory consistency model since it does not reorder accesses within a thread.

While the previous techniques are targeted at hiding memory access latency, multithreading can potentially hide the latency of any long-latency event just as easily, as long as the event can be detected at runtime. This includes synchronization and instruction latency as well.

This trend may change in future, as latencies are becoming increasingly longer as compared to processor speeds. Also with more sophisticated microprocessors that already provide methods that can be extended for multithreading, and with new multithreading techniques being developed to combine multithreading with instruction-level parallepsm, this trend certainly seems to be undergoing some change in future.