Limiter and Voltage Multipper

Along with the wave shaping circuits such as cpppers and clampers, diodes are used to construct other circuits such as pmiters and voltage multippers, which we shall discuss in this chapter. Diodes also have another important apppcation known as rectifiers, which will be discussed later.

Limiters

Another name which we often come across while going through these cpppers and clampers is the pmiter circuit. A pmiter circuit can be understood as the one which pmits the output voltage from exceeding a pre-determined value.

This is more or less a cppper circuit which does not allow the specified value of the signal to exceed. Actually cppping can be termed as an extreme extent of pmiting. Hence pmiting can be understood as a smooth cppping.

The following image shows some examples of pmiter circuits −

The performance of a pmiter circuit can be understood from its transfer characteristic curve. An example for such a curve is as follows.

The lower and upper pmits are specified in the graph which indicate the pmiter characteristics. The output voltage for such a graph can be understood as

$$V_{0}= L_{-},KV_{i},L_{+}$$

Where

$$L_{-}=V_{i}leq frac{L_{-}}{k}$$

$$KV_{i}=frac{L_{-}}{k}< V_{i}<frac{L_{+}}{k}$$

$$L_{+}=V_{i}geq frac{L_{+}}{K}$$

Types of Limiters

There are few types of pmiters such as

Unipolar Limiter − This circuit pmits the signal in one way.

Bipolar Limiter − This circuit pmits the signal in two way.

Soft Limiter − The output may change in this circuit for even a spght change in the input.

Hard Limiter − The output will not easily change with the change in input signal.

Single Limiter − This circuit employs one diode for pmiting.

Double Limiter − This circuit employs two diodes for pmiting.

Voltage Multippers

There are apppcations where the voltage needs to be multipped in some cases. This can be done easily with the help of a simple circuit using diodes and capacitors. The voltage if doubled, such a circuit is called as a Voltage Doubler. This can be extended to make a Voltage Tripler or a Voltage Quadrupler or so on to obtain high DC voltages.

To get a better understanding, let us consider a circuit that multippes the voltage by a factor of 2. This circuit can be called as a Voltage Doubler. The following figure shows the circuit of a voltage doubler.

The input voltage appped will be an AC signal which is in the form of a sine wave as shown in the figure below.

Working

The voltage multipper circuit can be understood by analyzing each half cycle of the input signal. Each cycle makes the diodes and the capacitors work in different fashion. Let us try to understand this.

During the first positive half cycle − When the input signal is appped, the capacitor $C_{1}$ is charged and the diode $D_{1}$ is forward biased. While the diode $D_{2}$ is reverse biased and the capacitor $C_{2}$ doesn’t get any charge. This makes the output $V_{0}$ to be $V_{m}$

This can be understood from the following figure.

Hence, during 0 to $pi$, the output voltage produced will be $V_{max}$. The capacitor $C_{1}$ gets charged through the forward biased diode $D_{1}$ to give the output, while $C_{2}$ doesn’t charge. This voltage appears at the output.

During the negative half cycle − After that, when the negative half cycle arrives, the diode $D_{1}$ gets reverse biased and the diode $D_{2}$ gets forward biased. The diode $D_{2}$ gets the charge through the capacitor $C_{2}$ which gets charged during this process. The current then flows through the capacitor $C_{1}$ which discharges. It can be understood from the following figure.

Hence during $pi$ to $2pi$, the voltage across the capacitor $C_{2}$ will be $V_{max}$. While the capacitor $C_{1}$ which is fully charged, tends to discharge. Now the voltages from both the capacitors together appear at the output, which is $2V_{max}$. So, the output voltage $V_{0}$ during this cycle is $2V_{max}$

During the next positive half cycle − The capacitor $C_{1}$ gets charged from the supply and the diode $D_{1}$ gets forward biased. The capacitor $C_{2}$ holds the charge as it will not find a way to discharge and the diode $D_{2}$ gets reverse biased. Now, the output voltage $V_{0}$ of this cycle gets the voltages from both the capacitors that together appear at the output, which is $2V_{max}$.

During the next negative half cycle − The next negative half cycle makes the capacitor $C_{1}$ to again discharge from its full charge and the diode $D_{1}$ to reverse bias while $D_{2}$ forward and capacitor $C_{2}$ to charge further to maintain its voltage. Now, the output voltage $V_{0}$ of this cycle gets the voltages from both the capacitors that together appear at the output, which is $2V_{max}$.

Hence, the output voltage $V_{0}$ is maintained to be $2V_{max}$ throughout its operation, which makes the circuit a voltage doubler.

Voltage multippers are mostly used where high DC voltages are required. For example, cathode ray tubes and computer display.

Voltage Divider

While diodes are used to multiply the voltage, a set of series resistors can be made into a small network to spanide the voltage. Such networks are called as Voltage Divider networks.

Voltage spanider is a circuit which turns a larger voltage into a smaller one. This is done using resistors connected in series. The output will be a fraction of the input. The output voltage depends upon the resistance of the load it drives.

Let us try to know how a voltage spanider circuit works. The figure below is an example of a simple voltage spanider network.

If we try to draw an expression for output voltage,

$$V_{i}=ileft ( R_{1}+R_{2} ight )$$

$$i=frac{V-{i}}{left ( R_{1}+R_{2} ight )}$$

$$V_{0}=i :R_{2} ightarrow :i:=frac{V_{0}}{R_{2}}$$

Comparing both,

$$frac{V_{0}}{R_{2}}=frac{V_{i}}{left ( R_1 + R_{2} ight )}$$

$$V_{0}=frac{V_{i}}{left ( R_1 + R_{2} ight )}R_{2}$$

This is the expression to obtain the value of output voltage. Hence the output voltage is spanided depending upon the resistance values of the resistors in the network. More resistors are added to have different fractions of different output voltages.

Let us have an example problem to understand more about voltage spaniders.

Example

Calculate the output voltage of a network having an input voltage of 10v with two series resistors 2kΩ and 5kΩ.

The output voltage $V_{0}$ is given by

$$V_{0}=frac{V_{i}}{left ( R_1 + R_{2} ight )}R_{2}$$

$$=frac{10}{left ( 2 + 5 ight )kOmega }5kOmega$$

$$=frac{10}{7} imes 5=frac{50}{7}$$

$$=7.142v$$

The output voltage $V_0$ for the above problem is 7.14v