Digital Communication - Delta Modulation

The samppng rate of a signal should be higher than the Nyquist rate, to achieve better samppng. If this samppng interval in Differential PCM is reduced considerably, the sampleto-sample ampptude difference is very small, as if the difference is 1-bit quantization, then the step-size will be very small i.e., Δ (delta).

Delta Modulation

The type of modulation, where the samppng rate is much higher and in which the stepsize after quantization is of a smaller value Δ, such a modulation is termed as delta modulation.

Features of Delta Modulation

Following are some of the features of delta modulation.

An over-sampled input is taken to make full use of the signal correlation.

The quantization design is simple.

The input sequence is much higher than the Nyquist rate.

The quapty is moderate.

The design of the modulator and the demodulator is simple.

The stair-case approximation of output waveform.

The step-size is very small, i.e., Δ (delta).

The bit rate can be decided by the user.

This involves simpler implementation.

Delta Modulation is a simppfied form of DPCM technique, also viewed as 1-bit DPCM scheme. As the samppng interval is reduced, the signal correlation will be higher.

Delta Modulator

The Delta Modulator comprises of a 1-bit quantizer and a delay circuit along with two summer circuits. Following is the block diagram of a delta modulator.

The predictor circuit in DPCM is replaced by a simple delay circuit in DM.

From the above diagram, we have the notations as −

$x(nT_{s})$ = over sampled input

$e_{p}(nT_{s})$ = summer output and quantizer input

$e_{q}(nT_{s})$ = quantizer output = $v(nT_s)$

$widehat{x}(nT_{s})$ = output of delay circuit

$u(nT_{s})$ = input of delay circuit

Using these notations, now we shall try to figure out the process of delta modulation.

$e_{p}(nT_{s}) = x(nT_{s}) - widehat{x}(nT_{s})$

---------equation 1

$= x(nT_{s}) - u([n - 1]T_{s})$

$= x(nT_{s}) - [widehat{x} [[n - 1]T_{s}] + v[[n-1]T_{s}]]$

---------equation 2

Further,

$v(nT_{s}) = e_{q}(nT_{s}) = S.sig.[e_{p}(nT_{s})]$

---------equation 3

$u(nT_{s}) = widehat{x}(nT_{s})+e_{q}(nT_{s})$

Where,

$widehat{x}(nT_{s})$ = the previous value of the delay circuit

$e_{q}(nT_{s})$ = quantizer output = $v(nT_s)$

Hence,

$u(nT_{s}) = u([n-1]T_{s}) + v(nT_{s})$

---------equation 4

Which means,

The present input of the delay unit

= (The previous output of the delay unit) + (the present quantizer output)

Assuming zero condition of Accumulation,

$u(nT_{s}) = S displaystylesumpmits_{j=1}^n sig[e_{p}(jT_{s})]$

Accumulated version of DM output = $displaystylesumpmits_{j = 1}^n v(jT_{s})$

---------equation 5

Now, note that

$widehat{x}(nT_{s}) = u([n-1]T_{s})$

$= displaystylesumpmits_{j = 1}^{n - 1} v(jT_{s})$

---------equation 6

Delay unit output is an Accumulator output lagging by one sample.

From equations 5 & 6, we get a possible structure for the demodulator.

A Stair-case approximated waveform will be the output of the delta modulator with the step-size as delta (Δ). The output quapty of the waveform is moderate.

Delta Demodulator

The delta demodulator comprises of a low pass filter, a summer, and a delay circuit. The predictor circuit is epminated here and hence no assumed input is given to the demodulator.

Following is the diagram for delta demodulator.

From the above diagram, we have the notations as −

$widehat{v}(nT_{s})$ is the input sample

$widehat{u}(nT_{s})$ is the summer output

$ar{x}(nT_{s})$ is the delayed output

A binary sequence will be given as an input to the demodulator. The stair-case approximated output is given to the LPF.

Low pass filter is used for many reasons, but the prominent reason is noise epmination for out-of-band signals. The step-size error that may occur at the transmitter is called granular noise, which is epminated here. If there is no noise present, then the modulator output equals the demodulator input.

Advantages of DM Over DPCM

1-bit quantizer

Very easy design of the modulator and the demodulator

However, there exists some noise in DM.

Slope Over load distortion (when Δ is small)

Granular noise (when Δ is large)

Adaptive Delta Modulation (ADM)

In digital modulation, we have come across certain problem of determining the step-size, which influences the quapty of the output wave.

A larger step-size is needed in the steep slope of modulating signal and a smaller stepsize is needed where the message has a small slope. The minute details get missed in the process. So, it would be better if we can control the adjustment of step-size, according to our requirement in order to obtain the samppng in a desired fashion. This is the concept of Adaptive Delta Modulation.

Following is the block diagram of Adaptive delta modulator.

The gain of the voltage controlled amppfier is adjusted by the output signal from the sampler. The amppfier gain determines the step-size and both are proportional.

ADM quantizes the difference between the value of the current sample and the predicted value of the next sample. It uses a variable step height to predict the next values, for the faithful reproduction of the fast varying values.