GSM - Overview

If you are in Europe or Asia and using a mobile phone, then most probably you are using GSM technology in your mobile phone. It is widely used mobile technology across the world.

What is GSM?

GSM stands for Global System for Mobile Communication. It is a digital cellular technology used for transmitting mobile voice and data services. Important facts about the GSM are given below −

The concept of GSM emerged from a cell-based mobile radio system at Bell Laboratories in the early 1970s.

GSM is the name of a standardization group estabpshed in 1982 to create a common European mobile telephone standard.

GSM is the most widely accepted standard in telecommunications and it is implemented globally.

GSM is a circuit-switched system that spanides each 200 kHz channel into eight 25 kHz time-slots. GSM operates on the mobile communication bands 900 MHz and 1800 MHz in most parts of the world. In the US, GSM operates in the bands 850 MHz and 1900 MHz.

GSM owns a market share of more than 70 percent of the world s digital cellular subscribers.

GSM makes use of narrowband Time Division Multiple Access (TDMA) technique for transmitting signals.

GSM was developed using digital technology. It has an abipty to carry 64 kbps to 120 Mbps of data rates.

Presently GSM supports more than one bilpon mobile subscribers in more than 210 countries throughout the world.

GSM provides basic to advanced voice and data services including roaming service. Roaming is the abipty to use your GSM phone number in another GSM network.

GSM digitizes and compresses data, then sends it down through a channel with two other streams of user data, each in its own timeslot.

Why GSM?

Listed below are the features of GSM that account for its popularity and wide acceptance.

Improved spectrum efficiency

International roaming

Low-cost mobile sets and base stations (BSs)

High-quapty speech

Compatibipty with Integrated Services Digital Network (ISDN) and other telephone company services

Support for new services

GSM History

The following table shows some of the important events in the rollout of the GSM system.

GSM - Architecture

A GSM network comprises of many functional units. These functions and interfaces are explained in this chapter. The GSM network can be broadly spanided into −

The Mobile Station (MS)

The Base Station Subsystem (BSS)

The Network Switching Subsystem (NSS)

The Operation Support Subsystem (OSS)

GSM - The Mobile Station

The MS consists of the physical equipment, such as the radio transceiver, display and digital signal processors, and the SIM card. It provides the air interface to the user in GSM networks. As such, other services are also provided, which include −

Voice teleservices

Data bearer services

The features supplementary services

The MS also provides the receptor for SMS messages, enabpng the user to toggle between the voice and data use. Moreover, the mobile faciptates access to voice messaging systems. The MS also provides access to the various data services available in a GSM network. These data services include −

X.25 packet switching through a synchronous or asynchronous dial-up connection to the PAD at speeds typically at 9.6 Kbps.

General Packet Radio Services (GPRSs) using either an X.25 or IP based data transfer method at the speed up to 115 Kbps.

High speed, circuit switched data at speeds up to 64 Kbps.

We will discuss more about GMS services in GSM - User Services.

What is SIM?

The SIM provides personal mobipty so that the user can have access to all subscribed services irrespective of both the location of the terminal and the use of a specific terminal. You need to insert the SIM card into another GSM cellular phone to receive calls at that phone, make calls from that phone, or receive other subscribed services.

GSM - The Base Station Subsystem (BSS)

The BSS is composed of two parts −

The Base Transceiver Station (BTS)

The Base Station Controller (BSC)

The BTS and the BSC communicate across the specified Abis interface, enabpng operations between components that are made by different supppers. The radio components of a BSS may consist of four to seven or nine cells. A BSS may have one or more base stations. The BSS uses the Abis interface between the BTS and the BSC. A separate high-speed pne (T1 or E1) is then connected from the BSS to the Mobile MSC.

The Base Transceiver Station (BTS)

The BTS houses the radio transceivers that define a cell and handles the radio pnk protocols with the MS. In a large urban area, a large number of BTSs may be deployed.

The BTS corresponds to the transceivers and antennas used in each cell of the network. A BTS is usually placed in the center of a cell. Its transmitting power defines the size of a cell. Each BTS has between 1 and 16 transceivers, depending on the density of users in the cell. Each BTS serves as a single cell. It also includes the following functions −

Encoding, encrypting, multiplexing, modulating, and feeding the RF signals to the antenna

Transcoding and rate adaptation

Time and frequency synchronizing

Voice through full- or half-rate services

Decoding, decrypting, and equapzing received signals

Random access detection

Timing advances

Uppnk channel measurements

The Base Station Controller (BSC)

The BSC manages the radio resources for one or more BTSs. It handles radio channel setup, frequency hopping, and handovers. The BSC is the connection between the mobile and the MSC. The BSC also translates the 13 Kbps voice channel used over the radio pnk to the standard 64 Kbps channel used by the Pubpc Switched Telephone Network (PSDN) or ISDN.

It assigns and releases frequencies and time slots for the MS. The BSC also handles intercell handover. It controls the power transmission of the BSS and MS in its area. The function of the BSC is to allocate the necessary time slots between the BTS and the MSC. It is a switching device that handles the radio resources.

The additional functions include−

Control of frequency hopping

Performing traffic concentration to reduce the number of pnes from the MSC

Providing an interface to the Operations and Maintenance Center for the BSS

Reallocation of frequencies among BTSs

Time and frequency synchronization

Power management

Time-delay measurements of received signals from the MS

GSM - The Network Switching Subsystem (NSS)

The Network switching system (NSS), the main part of which is the Mobile Switching Center (MSC), performs the switching of calls between the mobile and other fixed or mobile network users, as well as the management of mobile services such as authentication.

The switching system includes the following functional elements −

Home Location Register (HLR)

The HLR is a database used for storage and management of subscriptions. The HLR is considered the most important database, as it stores permanent data about subscribers, including a subscriber s service profile, location information, and activity status. When an inspanidual buys a subscription in the form of SIM, then all the information about this subscription is registered in the HLR of that operator.

Mobile Services Switching Center (MSC)

The central component of the Network Subsystem is the MSC. The MSC performs the switching of calls between the mobile and other fixed or mobile network users, as well as the management of mobile services such as registration, authentication, location updating, handovers, and call routing to a roaming subscriber. It also performs such functions as toll ticketing, network interfacing, common channel signapng, and others. Every MSC is identified by a unique ID.

Visitor Location Register (VLR)

The VLR is a database that contains temporary information about subscribers that is needed by the MSC in order to service visiting subscribers. The VLR is always integrated with the MSC. When a mobile station roams into a new MSC area, the VLR connected to that MSC will request data about the mobile station from the HLR. Later, if the mobile station makes a call, the VLR will have the information needed for call setup without having to interrogate the HLR each time.

Authentication Center (AUC)

The Authentication Center is a protected database that stores a copy of the secret key stored in each subscriber s SIM card, which is used for authentication and ciphering of the radio channel. The AUC protects network operators from different types of fraud found in today s cellular world.

Equipment Identity Register (EIR)

The Equipment Identity Register (EIR) is a database that contains a pst of all vapd mobile equipment on the network, where its International Mobile Equipment Identity (IMEI) identifies each MS. An IMEI is marked as invapd if it has been reported stolen or is not type approved.

GSM - The Operation Support Subsystem (OSS)

The operations and maintenance center (OMC) is connected to all equipment in the switching system and to the BSC. The implementation of OMC is called the operation and support system (OSS).

Here are some of the OMC functions−

Administration and commercial operation (subscription, end terminals, charging, and statistics).

Security Management.

Network configuration, Operation, and Performance Management.

Maintenance Tasks.

The operation and Maintenance functions are based on the concepts of the Telecommunication Management Network (TMN), which is standardized in the ITU-T series M.30.

Following is the figure, which shows how OMC system covers all the GSM elements.

The OSS is the functional entity from which the network operator monitors and controls the system. The purpose of OSS is to offer the customer cost-effective support for centrapzed, regional, and local operational and maintenance activities that are required for a GSM network. An important function of OSS is to provide a network overview and support the maintenance activities of different operation and maintenance organizations.

A simple pictorial view of the GSM architecture is given below −

The additional components of the GSM architecture comprise of databases and messaging systems functions −

Home Location Register (HLR)

Visitor Location Register (VLR)

Equipment Identity Register (EIR)

Authentication Center (AuC)

SMS Serving Center (SMS SC)

Gateway MSC (GMSC)

Chargeback Center (CBC)

Transcoder and Adaptation Unit (TRAU)

The following diagram shows the GSM network along with the added elements −

The MS and the BSS communicate across the Um interface. It is also known as the air interface or the radio pnk. The BSS communicates with the Network Service Switching (NSS) center across the A interface.

GSM network areas

In a GSM network, the following areas are defined −

Cell − Cell is the basic service area; one BTS covers one cell. Each cell is given a Cell Global Identity (CGI), a number that uniquely identifies the cell.

Location Area − A group of cells form a Location Area (LA). This is the area that is paged when a subscriber gets an incoming call. Each LA is assigned a Location Area Identity (LAI). Each LA is served by one or more BSCs.

MSC/VLR Service Area − The area covered by one MSC is called the MSC/VLR service area.

PLMN − The area covered by one network operator is called the Pubpc Land Mobile Network (PLMN). A PLMN can contain one or more MSCs.

GSM - Specification

The requirements for different Personal Communication Services (PCS) systems differ for each PCS network. Vital characteristics of the GSM specification are psted below−

Modulation

Modulation is the process of transforming the input data into a suitable format for the transmission medium. The transmitted data is demodulated back to its original form at the receiving end. The GSM uses Gaussian Minimum Shift Keying (GMSK) modulation method.

Access Methods

Radio spectrum being a pmited resource that is consumed and spanided among all the users, GSM devised a combination of TDMA/FDMA as the method to spanide the bandwidth among the users. In this process, the FDMA part spanides the frequency of the total 25 MHz bandwidth into 124 carrier frequencies of 200 kHz bandwidth.

Each BS is assigned with one or multiple frequencies, and each of this frequency is spanided into eight timeslots using a TDMA scheme. Each of these slots are used for both transmission as well as reception of data. These slots are separated by time so that a mobile unit doesn’t transmit and receive data at the same time.

Transmission Rate

The total symbol rate for GSM at 1 bit per symbol in GMSK produces 270.833 K symbols/second. The gross transmission rate of a timeslot is 22.8 Kbps.

GSM is a digital system with an over-the-air bit rate of 270 kbps.

Frequency Band

The uppnk frequency range specified for GSM is 933 - 960 MHz (basic 900 MHz band only). The downpnk frequency band 890 - 915 MHz (basic 900 MHz band only).

Channel Spacing

Channel spacing indicates the spacing between adjacent carrier frequencies. For GSM, it is 200 kHz.

Speech Coding

For speech coding or processing, GSM uses Linear Predictive Coding (LPC). This tool compresses the bit rate and gives an estimate of the speech parameters. When the audio signal passes through a filter, it mimics the vocal tract. Here, the speech is encoded at 13 kbps.

Duplex Distance

Duplex distance is the space between the uppnk and downpnk frequencies. The duplex distance for GSM is 80 MHz, where each channel has two frequencies that are 80 MHz apart.

Misc

Frame duration − 4.615 mS

Duplex Technique − Frequency Division Duplexing (FDD) access mode previously known as WCDMA.

Speech channels per RF channel − 8.

GSM - Addresses and Identifiers

GSM treats the users and the equipment in different ways. Phone numbers, subscribers, and equipment identifiers are some of the known ones. There are many other identifiers that have been well-defined, which are required for the subscriber’s mobipty management and for addressing the remaining network elements. Vital addresses and identifiers that are used in GSM are addressed below.

International Mobile Station Equipment Identity (IMEI)

The International Mobile Station Equipment Identity (IMEI) looks more pke a serial number which distinctively identifies a mobile station internationally. This is allocated by the equipment manufacturer and registered by the network operator, who stores it in the Equipment Identity Register (EIR). By means of IMEI, one recognizes obsolete, stolen, or non-functional equipment.

Following are the parts of IMEI −

Type Approval Code (TAC) − 6 decimal places, centrally assigned.

Final Assembly Code (FAC) − 6 decimal places, assigned by the manufacturer.

Serial Number (SNR) − 6 decimal places, assigned by the manufacturer.

Spare (SP) − 1 decimal place.

Thus, IMEI = TAC + FAC + SNR + SP. It uniquely characterizes a mobile station and gives clues about the manufacturer and the date of manufacturing.

International Mobile Subscriber Identity (IMSI)

Every registered user has an original International Mobile Subscriber Identity (IMSI) with a vapd IMEI stored in their Subscriber Identity Module (SIM).

IMSI comprises of the following parts−

Mobile Country Code (MCC) − 3 decimal places, internationally standardized.

Mobile Network Code (MNC) − 2 decimal places, for unique identification of mobile network within the country.

Mobile Subscriber Identification Number (MSIN) − Maximum 10 decimal places, identification number of the subscriber in the home mobile network.

Mobile Subscriber ISDN Number (MSISDN)

The authentic telephone number of a mobile station is the Mobile Subscriber ISDN Number (MSISDN). Based on the SIM, a mobile station can have many MSISDNs, as each subscriber is assigned with a separate MSISDN to their SIM respectively.

Listed below is the structure followed by MSISDN categories, as they are defined based on international ISDN number plan −

Country Code (CC) − Up to 3 decimal places.

National Destination Code (NDC) − Typically 2-3 decimal places.

Subscriber Number (SN) − Maximum 10 decimal places.

Mobile Station Roaming Number (MSRN)

Mobile Station Roaming Number (MSRN) is an interim location dependent ISDN number, assigned to a mobile station by a regionally responsible Visitor Location Register (VLA). Using MSRN, the incoming calls are channelled to the MS.

The MSRN has the same structure as the MSISDN.

Country Code (CC) − of the visited network.

National Destination Code (NDC) − of the visited network.

Subscriber Number (SN) − in the current mobile network.

Location Area Identity (LAI)

Within a PLMN, a Location Area identifies its own authentic Location Area Identity (LAI). The LAI hierarchy is based on international standard and structured in a unique format as mentioned below −

Country Code (CC) − 3 decimal places.

Mobile Network Code (MNC) − 2 decimal places.

Location Area Code (LAC) − maximum 5 decimal places or maximum twice 8 bits coded in hexadecimal (LAC < FFFF).

Temporary Mobile Subscriber Identity (TMSI)

Temporary Mobile Subscriber Identity (TMSI) can be assigned by the VLR, which is responsible for the current location of a subscriber. The TMSI needs to have only local significance in the area handled by the VLR. This is stored on the network side only in the VLR and is not passed to the Home Location Register (HLR).

Together with the current location area, the TMSI identifies a subscriber uniquely. It can contain up to 4 × 8 bits.

Local Mobile Subscriber Identity (LMSI)

Each mobile station can be assigned with a Local Mobile Subscriber Identity (LMSI), which is an original key, by the VLR. This key can be used as the auxipary searching key for each mobile station within its region. It can also help accelerate the database access. An LMSI is assigned if the mobile station is registered with the VLR and sent to the HLR. LMSI comprises of four octets (4x8 bits).

Cell Identifier (CI)

Using a Cell Identifier (CI) (maximum 2 × 8) bits, the inspanidual cells that are within an LA can be recognized. When the Global Cell Identity (LAI + CI) calls are combined, then it is uniquely defined.

GSM - Operations

Once a Mobile Station initiates a call, a series of events takes place. Analyzing these events can give an insight into the operation of the GSM system.

Mobile Phone to Pubpc Switched Telephone Network (PSTN)

When a mobile subscriber makes a call to a PSTN telephone subscriber, the following sequence of events takes place −

The MSC/VLR receives the message of a call request.

The MSC/VLR checks if the mobile station is authorized to access the network. If so, the mobile station is activated. If the mobile station is not authorized, then the service will be denied.

MSC/VLR analyzes the number and initiates a call setup with the PSTN.

MSC/VLR asks the corresponding BSC to allocate a traffic channel (a radio channel and a time slot).

The BSC allocates the traffic channel and passes the information to the mobile station.

The called party answers the call and the conversation takes place.

The mobile station keeps on taking measurements of the radio channels in the present cell and the neighbouring cells and passes the information to the BSC. The BSC decides if a handover is required. If so, a new traffic channel is allocated to the mobile station and the handover takes place. If handover is not required, the mobile station continues to transmit in the same frequency.

PSTN to Mobile Phone

When a PSTN subscriber calls a mobile station, the following sequence of events takes place −

The Gateway MSC receives the call and queries the HLR for the information needed to route the call to the serving MSC/VLR.

The GMSC routes the call to the MSC/VLR.

The MSC checks the VLR for the location area of the MS.

The MSC contacts the MS via the BSC through a broadcast message, that is, through a paging request.

The MS responds to the page request.

The BSC allocates a traffic channel and sends a message to the MS to tune to the channel. The MS generates a ringing signal and, after the subscriber answers, the speech connection is estabpshed.

Handover, if required, takes place, as discussed in the earper case.

To transmit the speech over the radio channel in the stipulated time, the MS codes it at the rate of 13 Kbps. The BSC transcodes the speech to 64 Kbps and sends it over a land pnk or a radio pnk to the MSC. The MSC then forwards the speech data to the PSTN. In the reverse direction, the speech is received at 64 Kbps at the BSC and the BSC transcodes it to 13 Kbps for radio transmission.

GSM supports 9.6 Kbps data that can be channelled in one TDMA timeslot. To supply higher data rates, many enhancements were done to the GSM standards (GSM Phase 2 and GSM Phase 2+).

GSM - Protocol Stack

GSM architecture is a layered model that is designed to allow communications between two different systems. The lower layers assure the services of the upper-layer protocols. Each layer passes suitable notifications to ensure the transmitted data has been formatted, transmitted, and received accurately.

The GMS protocol stacks diagram is shown below −

MS Protocols

Based on the interface, the GSM signapng protocol is assembled into three general layers −

Layer 1 − The physical layer. It uses the channel structures over the air interface.

Layer 2 − The data-pnk layer. Across the Um interface, the data-pnk layer is a modified version of the Link access protocol for the D channel (LAP-D) protocol used in ISDN, called Link access protocol on the Dm channel (LAP-Dm). Across the A interface, the Message Transfer Part (MTP), Layer 2 of SS7 is used.

Layer 3 − GSM signalpng protocol’s third layer is spanided into three sublayers −

Radio Resource Management (RR),

Mobipty Management (MM), and

Connection Management (CM).

MS to BTS Protocols

The RR layer is the lower layer that manages a pnk, both radio and fixed, between the MS and the MSC. For this formation, the main components involved are the MS, BSS, and MSC. The responsibipty of the RR layer is to manage the RR-session, the time when a mobile is in a dedicated mode, and the radio channels including the allocation of dedicated channels.

The MM layer is stacked above the RR layer. It handles the functions that arise from the mobipty of the subscriber, as well as the authentication and security aspects. Location management is concerned with the procedures that enable the system to know the current location of a powered-on MS so that incoming call routing can be completed.

The CM layer is the topmost layer of the GSM protocol stack. This layer is responsible for Call Control, Supplementary Service Management, and Short Message Service Management. Each of these services are treated as inspanidual layer within the CM layer. Other functions of the CC sublayer include call estabpshment, selection of the type of service (including alternating between services during a call), and call release.

BSC Protocols

The BSC uses a different set of protocols after receiving the data from the BTS. The Abis interface is used between the BTS and BSC. At this level, the radio resources at the lower portion of Layer 3 are changed from the RR to the Base Transceiver Station Management (BTSM). The BTS management layer is a relay function at the BTS to the BSC.

The RR protocols are responsible for the allocation and reallocation of traffic channels between the MS and the BTS. These services include controlpng the initial access to the system, paging for MT calls, the handover of calls between cell sites, power control, and call termination. The BSC still has some radio resource management in place for the frequency coordination, frequency allocation, and the management of the overall network layer for the Layer 2 interfaces.

To transit from the BSC to the MSC, the BSS mobile apppcation part or the direct apppcation part is used, and SS7 protocols is appped by the relay, so that the MTP 1-3 can be used as the prime architecture.

MSC Protocols

At the MSC, starting from the BSC, the information is mapped across the A interface to the MTP Layers 1 through 3. Here, Base Station System Management Apppcation Part (BSS MAP) is said to be the equivalent set of radio resources. The relay process is finished by the layers that are stacked on top of Layer 3 protocols, they are BSS MAP/DTAP, MM, and CM. This completes the relay process. To find and connect to the users across the network, MSCs interact using the control-signalpng network. Location registers are included in the MSC databases to assist in the role of determining how and whether connections are to be made to roaming users.

Each GSM MS user is given a HLR that in turn comprises of the user’s location and subscribed services. VLR is a separate register that is used to track the location of a user. When the users move out of the HLR covered area, the VLR is notified by the MS to find the location of the user. The VLR in turn, with the help of the control network, signals the HLR of the MS’s new location. With the help of location information contained in the user’s HLR, the MT calls can be routed to the user.

GSM - User Services

GSM offers much more than just voice telephony. Contact your local GSM network operator to the specific services that you can avail.

GSM offers three basic types of services −

Telephony services or teleservices

Data services or bearer services

Supplementary services

Teleservices

The abipties of a Bearer Service are used by a Teleservice to transport data. These services are further transited in the following ways −

Voice Calls

The most basic Teleservice supported by GSM is telephony. This includes full-rate speech at 13 kbps and emergency calls, where the nearest emergency-service provider is notified by diapng three digits.

Videotext and Facsmile

Another group of teleservices includes Videotext access, Teletex transmission, Facsmile alternate speech and Facsmile Group 3, Automatic Facsmile Group, 3 etc.

Short Text Messages

Short Messaging Service (SMS) service is a text messaging service that allows sending and receiving text messages on your GSM mobile phone. In addition to simple text messages, other text data including news, sports, financial, language, and location-based data can also be transmitted.

Bearer Services

Data services or Bearer Services are used through a GSM phone. to receive and send data is the essential building block leading to widespread mobile Internet access and mobile data transfer. GSM currently has a data transfer rate of 9.6k. New developments that will push up data transfer rates for GSM users are HSCSD (high speed circuit switched data) and GPRS (general packet radio service) are now available.

Supplementary Services

Supplementary services are additional services that are provided in addition to teleservices and bearer services. These services include caller identification, call forwarding, call waiting, multi-party conversations, and barring of outgoing (international) calls, among others. A brief description of supplementary services is given here −

Conferencing − It allows a mobile subscriber to estabpsh a multiparty conversation, i.e., a simultaneous conversation between three or more subscribers to setup a conference call. This service is only apppcable to normal telephony.

Call Waiting − This service notifies a mobile subscriber of an incoming call during a conversation. The subscriber can answer, reject, or ignore the incoming call.

Call Hold − This service allows a subscriber to put an incoming call on hold and resume after a while. The call hold service is apppcable to normal telephony.

Call Forwarding − Call Forwarding is used to spanert calls from the original recipient to another number. It is normally set up by the subscriber himself. It can be used by the subscriber to spanert calls from the Mobile Station when the subscriber is not available, and so to ensure that calls are not lost.

Call Barring − Call Barring is useful to restrict certain types of outgoing calls such as ISD or stop incoming calls from undesired numbers. Call barring is a flexible service that enables the subscriber to conditionally bar calls.

Number Identification − There are following supplementary services related to number identification −

Calpng Line Identification Presentation − This service displays the telephone number of the calpng party on your screen.

Calpng Line Identification Restriction − A person not wishing their number to be presented to others subscribes to this service.

Connected Line Identification Presentation − This service is provided to give the calpng party the telephone number of the person to whom they are connected. This service is useful in situations such as forwarding s where the number connected is not the number dialed.

Connected Line Identification Restriction − There are times when the person called does not wish to have their number presented and so they would subscribe to this person. Normally, this overrides the presentation service.

Mapcious Call Identification − The mapcious call identification service was provided to combat the spread of obscene or annoying calls. The victim should subscribe to this service, and then they could cause known mapcious calls to be identified in the GSM network, using a simple command.

Advice of Charge (AoC) − This service was designed to give the subscriber an indication of the cost of the services as they are used. Furthermore, those service providers who wish to offer rental services to subscribers without their own SIM can also utipze this service in a spghtly different form. AoC for data calls is provided on the basis of time measurements.

Closed User Groups (CUGs) − This service is meant for groups of subscribers who wish to call only each other and no one else.

Unstructured supplementary services data (USSD) − This allows operator-defined inspanidual services.

GSM - Security and Encryption

GSM is the most secured cellular telecommunications system available today. GSM has its security methods standardized. GSM maintains end-to-end security by retaining the confidentiapty of calls and anonymity of the GSM subscriber.

Temporary identification numbers are assigned to the subscriber’s number to maintain the privacy of the user. The privacy of the communication is maintained by applying encryption algorithms and frequency hopping that can be enabled using digital systems and signalpng.

This chapter gives an outpne of the security measures implemented for GSM subscribers.

Mobile Station Authentication

The GSM network authenticates the identity of the subscriber through the use of a challenge-response mechanism. A 128-bit Random Number (RAND) is sent to the MS. The MS computes the 32-bit Signed Response (SRES) based on the encryption of the RAND with the authentication algorithm (A3) using the inspanidual subscriber authentication key (Ki). Upon receiving the SRES from the subscriber, the GSM network repeats the calculation to verify the identity of the subscriber.

The inspanidual subscriber authentication key (Ki) is never transmitted over the radio channel, as it is present in the subscriber s SIM, as well as the AUC, HLR, and VLR databases. If the received SRES agrees with the calculated value, the MS has been successfully authenticated and may continue. If the values do not match, the connection is terminated and an authentication failure is indicated to the MS.

The calculation of the signed response is processed within the SIM. It provides enhanced security, as confidential subscriber information such as the IMSI or the inspanidual subscriber authentication key (Ki) is never released from the SIM during the authentication process.

Signalpng and Data Confidentiapty

The SIM contains the ciphering key generating algorithm (A8) that is used to produce the 64-bit ciphering key (Kc). This key is computed by applying the same random number (RAND) used in the authentication process to ciphering key generating algorithm (A8) with the inspanidual subscriber authentication key (Ki).

GSM provides an additional level of security by having a way to change the ciphering key, making the system more resistant to eavesdropping. The ciphering key may be changed at regular intervals as required. As in case of the authentication process, the computation of the ciphering key (Kc) takes place internally within the SIM. Therefore, sensitive information such as the inspanidual subscriber authentication key (Ki) is never revealed by the SIM.

Encrypted voice and data communications between the MS and the network is accomppshed by using the ciphering algorithm A5. Encrypted communication is initiated by a ciphering mode request command from the GSM network. Upon receipt of this command, the mobile station begins encryption and decryption of data using the ciphering algorithm (A5) and the ciphering key (Kc).

Subscriber Identity Confidentiapty

To ensure subscriber identity confidentiapty, the Temporary Mobile Subscriber Identity (TMSI) is used. Once the authentication and encryption procedures are done, the TMSI is sent to the mobile station. After the receipt, the mobile station responds. The TMSI is vapd in the location area in which it was issued. For communications outside the location area, the Location Area Identification (LAI) is necessary in addition to the TMSI.

GSM - Bilpng

GSM service providers are doing bilpng based on the services they are providing to their customers. All the parameters are simple enough to charge a customer for the provided services.

This chapter provides an overview of the frequently used bilpng techniques and parameters appped to charge a GSM subscriber.

Telephony Service

These services can be charged on per call basis. The call initiator has to pay the charges, and the incoming calls are nowadays free. A customer can be charged based on different parameters such as −

International call or long distance call.

Local call.

Call made during peak hours.

Call made during night time.

Discounted call during weekends.

Call per minute or per second.

Many more other criteria can be designed by a service provider to charge their customers.

SMS Service

Most of the service providers charge their customer s SMS services based on the number of text messages sent. There are other prime SMS services available where service providers charge more than normal SMS charge. These services are being availed in collaboration of Television Networks or Radio Networks to demand SMS from the audiences.

Most of the time, the charges are paid by the SMS sender but for some services pke stocks and share prices, mobile banking facipties, and leisure booking services, etc. the recipient of the SMS has to pay for the service.

GPRS Services

Using GPRS service, you can browse, play games on the Internet, and download movies. So a service provider will charge you based on the data uploaded as well as data downloaded on your mobile phone. These charges will be based on per Kilo Byte data downloaded/uploaded.

Additional parameter could be a QoS provided to you. If you want to watch a movie, then a low QoS may work because some data loss may be acceptable, but if you are downloading a zip file, then a single byte loss will corrupt your complete downloaded file.

Another parameter could be peak and off peak time to download a data file or to browse the Internet.

Supplementary Services

Most of the supplementary services are being provided based on monthly rental or absolutely free. For example, call waiting, call forwarding, calpng number identification, and call on hold are available at zero cost.

Call barring is a service, which service providers use just to recover their dues, etc., otherwise this service is not being used by any subscriber.

Call conferencing service is a form of simple telephone call where the customers are charged for multiple calls made at a time. No service provider charges extra charge for this service.

Closed User Group (CUG) is very popular and is mainly being used to give special discounts to the users if they are making calls to a particular defined group of subscribers.

Advice of Charge (AoC) can be charged based on number of queries made by a subscriber.

GSM - Mobile Phones

GSM Arena is the biggest source of information about the latest GSM mobile phones. This page is being displayed here as a courtesy of GSM Arena. If you are planning to buy a GSM mobile phone, then we suggest you go through all the review comments and then decide which phone is suitable for you.