CDMA - Multiple Access Methods

The possibipty to operate in either FDD or TDD mode is allowed for efficient use of available spectrum according to frequency allocation in different regions.

Frequency Division Duplex

A duplex method whereby the Uppnk and the Downpnk transmissions use two separate frequency bands −

Uppnk − 1920 MHz to 1980 MHz

Downpnk − 2110 MHz to 2170 MHz

Bandwidth − Each carrier is located on the center of a 5 MHz wide band

Channel Separation

Nominal value of 5 MHz that can be adjusted.

Channel Raster

200 kHz (center frequency must be a multiple of 200 kHz).

Tx-Rx Frequency Separation

Nominal value of 190 MHz. This value can be either fixed or variable (minimum of 134.8 and maximum of 245.2 MHz).

Channel Number

The carrier frequency is designated by the UTRA Absolute Radio Frequency Channel Number (UARFCN). This number is sent by the network (for the uppnk and downpnk) on the BCCH logical channel and is defined by Nu = 5 * (Frequency uppnk MHz) and ND = 5 * (Frequency downpnk MHz).

Time Division Duplex

Time spanision duplex is a technique by which the Uppnk and the Downpnk transmissions are carried over the same frequency by using synchronized time intervals. The carrier uses a 5 MHz band, although there is a low chip rate solution under study by the 3GPP (1.28 Mcps). The available frequency bands for TDD will be 1900–1920 MHz and 2010 – 2025 MHz.

Duplex Methods of Radio Links

In case of Time Division Duplex, the forward pnk frequency is same as the reverse pnk frequency. In each pnk, signals are transmitted continuously in turns − just pke a ping-pong game.

Example of TDD System

TDD uses a single frequency band for both to transmit and to receive. Further, it shares the band by assigning alternate timeslots for transmitting and receiving operations. The information to be transmitted can be voice, video, or computer data in bit-serial format. Each time interval can be 1 byte long or may be a part of several bytes.

TDD alternates the transmission and reception station data over time. Timeslots can be of variable length. Due to the nature of high-speed data, the communicating parties cannot mean that the transmissions are intermittent. Transmissions that appear as simultaneous are actually competing each other. Digitally converted into analog voice, no one can say that it is not a full duplex.

In some TDD systems, alternative time intervals are of same duration or having both DL and UL; however, the system does not need to be symmetric 50/50. The system may be asymmetrical as required.

For example, while accessing the Internet, the download speed is usually higher than the upload speed. Most of the equipment work on asynchronous mode where the download speed is higher than the upload speed. When the download speed is higher than the upload speed, less timeslots are needed for uploading. Some TDD formats offer dynamic bandwidth allocation when the number of time intervals or durations is changed on the fly as needed.

The real advantage of TDD is that it is only a single channel of the frequency spectrum and it doesn’t require band guards or channel separations as the intervals take place using timeslots. The disadvantage is that the successful implementation of TDD requires a timing system. The precise timing to both the transmitter and the receiver is needed to ensure that the time intervals do not overlap or interfere with another.

Timing is often synchronized to GPS atomic clock standards specific derivative. The guard time is also needed between timeslots to avoid duppcation. This time is generally equal to the transmission-reception processing time (transmission-reception switching time) and the transmission delays (latency) on the communications channel.

Frequency Division Duplex

In Frequency Division Duplex (FDD), the forward pnk frequency is not the same as the reverse pnk frequency. In each pnk, signals are continuously transmitted in parallel.

Example of FDD System

FDD requires two symmetrical segments of spectrum for the uppnk and downpnk channels.

In a cell phone with a transmitter and receiver, operating simultaneously in such close proximity, the receiver has to filter as much of the signal from the transmitter as possible. More separation of the spectrum, the most effective filters.

FDD uses a lot of frequency spectrum, generally twice of the required TDD spectrum. In addition, there must be adequate spectrum separation between transmission and reception of the channels. These bands keep saying − it cannot be used, they are unnecessary. Given the scarcity and cost of the spectrum, they are real disadvantages.

Use of FDD

FDD is widely used in different cellular telephone systems. In some systems, the band 869-894 MHz is used as the downpnk (DL) spectrum from the cell site tower to the device. And, the band 824-849 MHz is used as the uppnk (UL) spectrum of the handset at the cell site.

FDD also works on a cable where transmit and receive channels are given different parts of the cable spectrum, as in cable TV systems. And, filters are used to keep the channels separate.

Disadvantage of FDD

The drawback of FDD is that it does not allow special techniques pke multiple antennas, multiple input-output (MIMO), and beamforming. These technologies are an essential element of the new strategies Long Term Evolution (LTE) 4G cell phone to increase the data rate. It is difficult to make broad enough bandwidth to cover both sets of antenna spectrum. Circuit complex dynamic adjustment is required.

Multiple Access Methods

The radio channel is a communication medium shared by several users in a geographic area. Mobile stations are in competition with one another for the frequency resource to transmit their information flow. Without other measures to control concurrent access of several users, colpsions can occur. Since colpsions are undesirable for connectionoriented communication such as mobile phones, personal/mobile subscriber stations need to be allocated the dedicated channels on request.

The mobile communication, sharing wireless resources on all users, must be communicated to identify the user. While identifying the user, it is referred to as "multiple access" (Multiple Access) that is receiving a radio wave of a number of transmitting stations in a receiving station (as shown in the following image).